Eco-friendly recycled wool quilt

This warm and comfy quilt is made entirely from recycled materials.

You can play with patterns and textures, make it small or large, muted or funky. It's a fun, creative and inexpensive project.

WHAT YOU'LL NEED

Several wool sweaters (don't use cotton or synthetics, they won't felt)

A sheet or blanket for the lining

Another sheet or large fabric scrap that will be cut in strips for binding the blanket edges

If you're using a sheet or thin fabric for the lining, you could use quilt batting to make it thicker. I used fleece as my lining so it wasn't necessary.

The number of sweaters you'll need depends on the final size you want for your quilt. Keep in mind they'll shrink a lot when felted.

For a baby quilt like the one in the picture, I used 6 large sweaters.

SEWING INSTRUCTIONS

1. If you don't have enough old sweaters on hand, try garage sales or goodwill.

Don't forget to look through men sweaters, they're usually larger which is good.

Machine wash them in hot water with soap and put them in the dryer.

2. Cut the felted sweater into squares - the size is up to you. They will be easier to combine and sew if they're all the same size.

Of course you can use other shapes if you prefer.

Place the squares on the floor and decide how you'll combine them.

3. Sew the squares together as shown using a zigzag stitch, letting them overlap just a little. Assemble the squares into strips.

4. Sew the strips together using a zigzag stitch.

5. Place your work on top of the lining, wrong sides together. Put your batting in between if you chose to use some.

Pin and assemble by sewing over the zigzag stitches with a straight stitch.

Pinning is important so that both layers remain flat against each other.

6. Edges:

Cut four fabric strips. They should be 6 times larger than your desired binding width and a bit longer than each corresponding blanket edge.

Fold the strips in two and press. Sew the first strip along one edge as shown, on the lining side of the quilt.

7. Fold against the right side, pin and edgestitch as shown. Do the same thing with the opposite edge.

8. Finish with the two remaining edges, folding and sewing the ends as shown.

I used this tutorial as my inspiration.

Sew cute bloomers for your baby or toddler

This fun project doesn't require a lot of fabric so you can recycle old t-shirts and tops instead of buying new fabric. The bloomers in the picture are cut in one of my sister's old tops.

Use only stretch fabric for this project.

PATTERN AND CUTTING

For a 3 year old, print the pattern so that the reference line on the right measures 10cm.

Scale it up or down for an older or younger child (you won't need to scale it a lot).

A: Cut 1 in main fabric

B: Cut 2 in main fabric

C: Cut 1 in main fabric

D: Cut 1 in contrasting fabric - optional

E: Elastic, 1cm wide or narrower (enough for waist and both leg openings, depends on your toddler's size)

Dotted lines: place on fabric fold

Red lines = seam allowances

Grey areas = wrong side

White areas = right side

Illustration 1 shows how to place the pieces on the fabric fold (use a different fabric for piece D). However, there are better ways to do it if you want to save fabric.

SEWING INSTRUCTIONS

Sew the heart or any other appliqué you like on piece A, using a zigzag stitch. Don't place it too close to the edges.

Cut your elastic. Waist: your child's waist circumference minus 3cm (I cut 42cm for my 3 year old).

Leg openings: your child's thigh circumference minus 1.5cm (26 cm for my 3 year old).

Assemble piece A and both pieces B as shown, sewing 1cm from the edges. If your machine doesn't have a stretch stitch, use a very narrow zigzag stitch.

When you're done, roll up piece A so that it stays out of the way.

Sew piece C as shown, right side facing up, 1cm from the edges.

Trim the seam allowances to reduce bulkiness.

Turn inside out.

Sew 1cm from the edges. Trim and finish sides with a zigzag stitch if you like.

Fold the waist edge as shown (1.5cm wide). Sew along the edge with a narrow zigzag, leaving a 3cm hole to insert the elastic.

Attach a safety pin to the elastic and slide it inside waistband.

Sew the elastic ends together, tuck it in and finish the waist.

Do the same for the remaining elastics.

Please note that the panties in the first pic were finished using a serger. With an ordinary machine and the zigzag stitch method described in the tut, it will look more like this (use a narrower elastic for a more discreet finish):